Showing posts with label Amplifier. Show all posts
Showing posts with label Amplifier. Show all posts

AF Amplifier With Digital Volume Control Based On TDA8551 Circuit Schematic With explanation

The Philips Semiconductors TDA8551 is a small audio amplifier with an integrated volume control. When operated from +5 V, it delivers a nominal output power of more than one watt into 8 ohms. It can also be used over a supply voltage range of +2.7 to +5.5 V, with correspondingly reduced output power. The output volume can be adjusted from –60 dB to +20 dB in 64 steps, using a set of up and down push-buttons. The shared UP/DOWN input for the up and down switches has three states. If it is ‘?oating’, which means that both of the switches are open, the volume remains unchanged. A pulse to earth decreases the volume by 1.25 dB, while a positive pulse increases the volume by 1.25 dB.
AF Amplifier With Digital Up Down Volume Control Based On TDA8551
Add caption
When the power is switched on, the internal counter takes on the –20 dB setting. An additional input (MODE) allows the amplifier to be switched from the operating state to the mute or standby state. If this input is held at the earth level, the amplifier is operational. If +5 V is applied to this pin, the TDA8551 enters the Standby mode, in which the current consumption drops from the typical operational level of 6mA to less than 10µA. Finally, the MODE input can be used as a mute input by applying a voltage of 1 t0 3.6 V to this input. This voltage can be provided by a connection to the SCR pin, which lies at half of the operating voltage and to which a filter capacitor is connected.
TDA8551/TDA8551T Pinout DiagramThe loudspeaker is connected in a floating configuration between the two outputs of the bridge amplifier in the TDA8551. This provides the desired output power level, in spite of the lowsupply voltage . For headphone applications, which do not need as much output power, you can connect the headphone between earth and one of the outputs, via an electrolytic coupling capacitor. You can make a stereo headphone amplifier in this way, using two TDS8551 ICs. The TDA8551 is housed in a DIP8 package. The SMD version is the TDA8551T, in an SO8 package.
For More Projects Please Visit www.extremecircuits.net
Elektor06-2010/NutsVolts06-2010/NutsVolts06-2010/Elektor303Circuit/PracticalArduino/Elektor05-2010

Photovoltaic Transimpedance Amplifier Circuit Diagram

Photovoltaic Transimpedance Amplifier Circuit Diagram
The following schematic shows the Photovoltaic Transimpedance Amplifier Circuit Diagram. This design combines two Intersil X9258T digitally controlled potentiometers with an AD822 low noise dual op amp to create a flexible, digitally calibrated, wide dynamic range transimpedance amplifier topology that can be used with virtually any photovoltaic detector technology. The amplifier output is given by:

Vo = Is(1MΩ) ((1+P1)/(256-P1))

Where P1 is the 8-bit (0 to 255) digital value written to DCP1. For more detail information on Photovoltaic Transimpedance Amplifier Circuit Diagram, download the following file.

LA3161 based Preamplifier circuit with explanation

LA3161 based Preamplifier circuit with explanation


Preamplifiers are used to amplify low level signals such as those from mikes, tape heads before they are fed into power amplifiers. Power amplifiers are generally less sensitive. Frequency response also can be suitably trimmed and modified at preamp stage. LA 3161 is one of those widely used in tape decks and amplifiers as a stereo preamplifier.LA3161 based Preamplifier circuit with explanationLA3161 based Preamplifier circuit with explanation


Block Diagram is shown in Figure. LA 3161 has two low noise preamplifiers with good ripple rejection on chip catering to stereo applications. External part count is low and Single In line (SIL))(Figure 43) package makes mounting easy. Wltile the operating voltage is 9V, the IC can tolerate voltages up to 18V. Typical input resistance is WOK and output resistance is 10K with an open loop gain of78dB. Block diagram of the IC is given below. Input is given at Pin 1 and 8, output is taken at Pin 3 and 6, and negative Feedback is given at Pin 2 and 7. Power is at Pin 5 and Pin 4 is the ground terminal. There is an internal voltage regulator.

Ready made PCBs, even populated PCBs are available using this very useful IC. You can still build one, with a Veroboard provided proper care is taken about the ground returns. It simply means that one should not connect ground terminals of output and input at the same place. This will create serious oscillations and normal hobbyist will be left in the woods. Please read general instructions for working with amplifiers in the end.

VHF RF Single-Chip Preamplifier circuit with explanation

Here is a high performance RF amplifier for the entire VHF broadcast and PMR band (100-175 MHz) which can be successfully built without any special test equipment. The grounded-gate configuration is inherently stable without any neutralization if appropriate PCB layout techniques are employed. The performance of the amplifier is quite good.
The noise figure is below 2 dB and the gain is over 13 dB. The low noise figure and good gain will help car radios or home stereo receivers pick up the lower-power local or campus radio stations, or distant amateur VHF stations in the 2-metres band. Due to the so-called threshold effect, FM receivers loose signals abruptly so if your favourite station fades in and out as you drive, this amplifier can cause a dramatic improvement.
The MAX2633 is a low-voltage, low-noise amplifier for use from VHF to SHF frequencies. Operating from a single +2.7 V to +5.5V supply, it has a virtually flat gain response to 900 MHz. Its low noise figure and low supply current makes it ideal for RF receive, buffer and transmit applications. The MAX2633 is biased internally and has a user-selectable supply current, which can be adjusted by adding a single external resistor (here, R1). This circuit draws only 3 mA current.

VHF RF preamplifier circuit diagram

VHF RF Single-Chip Preamplifier circuit with explanation


Besides a single bias resistor, the only external components needed for the MAX2630 family of RF amplifiers are input and output blocking capacitors, C1 and C3, and a VCC bypass capacitor, C2. The coupling capacitors must be large enough to contribute negligible reactance in a 50-Ω system at the lowest operating frequency. Use the following equation to calculate their minimum value:
Cc = 53000/ flow [pF]

 

150W LM12 based audio amplifier circuit with explanation

LM12 operational amplifier can output currents up to 10A. The LM12 in encapsulated in TO-3 with 4 pins, can support up to 800W and has enough internal protections to prevent slacks from over-currents or over-heating.
You can use LM12CL with 30 V maximum voltage or LM12C with 40V maximum.
The L1 coil has 40 turns 1mm copper, coiled over R4. If you use LM12CL it is recomended to have toroidal transformer 2 x 22V. The output must be between 7 and 12A. Filtering capacitors must have at least 20.000 uF.
LM12 must be mounted with screws on a big heatsink (=< 1.50 C/W) and electric isolated form the heatsink

LM12 amplifier circuit diagram

LM12 amplifier PCB layout






More audio amplifier circuits…

TDA2003(Dual ) based 18W Bridge Amplifier circuit with explanation

The following schematic diagram is the diagram of 18W power amplifier. This amplifier built using 2 pieces of power ICs of TDA2003 with bridge connection (dual TDA2003). A TDA2003 gives 10W power output.
Circuit design:
18W TDA2003 bridge amplifier circuit
PCB layout:

TDA2003 18W bridge Amplifier PCB layout
Download TDA2003 Datasheet

TDA1562 bassed One-IC 50W Audio Amplifier circuit with explanation

The integrated output amplifier described in this article consists of little more than one integrated circuit. It is intended especially for use in motor vehicles and other battery-operated applications. Although it appears simple and hardly worth looking at, the amplifier can produce an appreciable audio power output. The circuit diagram in Figure 2 emphasizes how few external components are needed to construct a complete output amplifier.

One-IC 50W Audio Power Amplifier Using TDA1562 circuit project

For instance, the new device does not need compensation networks to enhance the stability. Also, because of the absence of switch-on phenomena, there is no need for a switch-on delay network. There is, of course, still a need for supply line decoupling capacitors. Capacitors C5 and C6 are required for Class-H operation, about which more in the box. The value of input capacitors C1 and C2 is relatively low, thanks to the high input impedance of the IC. Switched RC network R4-C4 at the ‘mode select’ input (pin 4) serves to switch the IC to ‘mute’ or ‘standby’.

One-IC 50W Audio Power Amplifier Using TDA1562 circuit diagram

When the supply voltage is switched on, the IC is first switched automatically to the ‘mute’ mode and to ‘on’ only after a short delay. The time constant R4-C4 is a few tenths of a second and this delay between the two states is sufficient to obviate disturbing (and annoying) switch-on phenomena. Switch S1 enables the amplifier to be switched to ‘standby' when the use of the amplifier is not needed for a period of time. When that time has elapsed, the amplifier is quickly reverted to normal operation. The current drain in the standby mode is virtually negligible at only 200µA. Resistor R3 prevents a short-circuit current ensuing when S1 is being closed at the instant C4 is being discharged.

One-IC 50W Audio Power Amplifier Using TDA1562 circuit

One-IC 50W Audio Power Amplifier Using TDA1562 circuit schematic

Measurement results (at Ub=14.4 V)
Supply voltage

* 8–18 V

Sensitivity

* 760 mV r.m.s.

Input impedance

* 70 kΩ

Power output

* 54 W r.m.s. into 4 Ω (f=1 kHz; THD+N=1%)

Harmonic distortion (THD+N)

* at 1 W into 4 Ω: 0.046% (1 kHz)
* 0.29% (20 kHz)
* at 35 W into 4 Ω: 0.12% (1 kHz)
* 0.7% (20 kHz)

Signal-to-noise ratio (with 1 W into 4 Ω)

* 88 dBA

Power bandwidth

* 7.5 Hz – 185 kHz (at 25 W into 4 Ω)

Quiescent current

* about 135 mA (‘on’)

Resistors:

* R1 = 1MΩ
* R2 = 4kΩ7
* R3 = 1kΩ
* R4 = 100kΩ

Capacitors:

* C1,C2 = 470nF
* C3,C4 = 10µF 63V radial
* C5,C6,C8 = 4700µF 25V radial
* (18mm max. dia., raster 7.5 mm)
* C7 = 100nF, raster 5 mm

Semiconductors:

* D1 = high-efficiency-LED
* IC1 = TDA1562Q (Philips)

Miscellaneous:

* S1 = single-pole on/off switch
* Four spade connectors, PCB mount Heatsink for IC1 (Rth<2.5 K/W)

NJM2582 bassed 4-channel video amplifier electronic project circuit with explanation

 NJM2582 bassed 4-channel video amplifier electronic project circuit with explanation

A very simple 4 channel video amplifier electronic circuit project can be designed using NJM2582 ic suitable for video applications with SCART connector . Design of the circuit is very simple and require few external electronic parts .

Some features of the NJM2582 are : Operating Voltage ±5V, +5V, +11V ; 6input 4output , 2input 1output Video SW , Internal LPF , 6dB Amplifier , Internal 75Ω Driver Circuit , DC output for SCART (FUNCTION SW, BLANKING) .

high gain antenna 43dB amplifier circuit

 high gain antenna 43dB amplifier circuit

A very simple and useful antenna amplifier can be constructed using this circuit diagram . This antenna amplifier is very useful for 35kHz-150Mhz frequency band . This antenna amplifier circuit is based on transistors and has a low 3 dB non-linearity and a high gain of 43 dB . The input and output impedance for this rf amplifier is 75 ohms . The L1 and L2 radio frequency coils are constructed from a 0.25 mm CuEm wire , with a 5 mm diameter . Both coils require 10 number of turns .

All used transistors are of the same type and can be BF183, BF200 or other similar type . The total consumption of this rf amplifier is very low , the circuit will need only 20 mA .
This rf amplifier circuit needs to be powered from a 12.5 volts DC power supply circuit .


IC-RD15HVF1 bassed RF amplifier electronic circuit project with explanation

This RF amplifier electronic project circuit is designed for 525MHz frequency band . This RF amplifier electronic project is based on the RD15HVF1 MOS FET type transistor specifically
designed for VHF/UHF High power amplifiers .
This RD15HVF1 rf amplifier circuit project can provide a maximum High power of 15 watts and a gain power more than 7dB using few external electronic parts . This amplifier circuit project must be powered from a 12 volts dc power supply .

C1 capacitance must have a value of 10uFand must be formed from 2200pf capacitors connected in parallel . C2 capacitor must be formed from two capacitors of 2200pf connected in parallel . C3 capacitance must have a value of 330uF and must be formed from 2200pf capacitors connected in parallel . L1 L2 and L3 coils must be formed from 1.6mm silver plateted copper wire on a diameter of 6mm . L1 must have 4 turns , L2 must have 2 turns and L3 must have 4 turns .
IC-RD15HVF1 bassed RF amplifier electronic circuit project with explanation
As you can see in schematic circuit , this electronic project based on MOS FET type transistor require few external electronic parts .

250mW 16-dB VHF amplifier circuit project with explanation

A high efficiency simple 2-transistor VHF amplifier electronic circuit project can be designed using this electronic circuit diagram . This VHF amplifier electronic circuit has a very high efficiency of about 16dB gain, and requires no tuning or alignment procedures. Wideband techniques have been used in the design and the circuit is equipped with a "lowpass" filter to ensure good output spectral purity. This VHF power amplifier circuit is specifically designed to amplify the output of 7mW to 10mW WBFM transmitters to a final level of 250mW to 300mW, after the filter.
The output of this stage is around 70mW of RF power.
The transistor is biased by means of R5, R6 and L6, and the residual DC current is set by R4. The input signal is coupled by C9 to the Base of the transistor.
The input signal from Q1 is coupled to the Base of Q2 via C7.The 78L08 voltage regulator is used to regulate the supply voltage to Q1 and the bias votages to both Q1 and Q2 so that the output RF power is relatively constant, even with large variations of supply voltage.
The output of the amplifier is filtered with a low-pass filter to reduce the output spurious and harmonic content.
The output filter consists of C3, C4, L1 and L2.
This RF power amplifier must be powered from a simple 12 volts DC power supply circuit.
250mW  16-dB   VHF amplifier circuit project with explanation

470 mWatts audio amplifier for portable applications

A very simple audio amplifier electronic project can be designed using this circuit diagram . This audio amplifier project can be used in small audio circuits that not require much audio power .
This audio amplifier electronic project will provide a 470 mwatts output poThis circuit has less than 2% distortion and is flat within 3 dB from 15Hz to 130kHz .
As you can see in the schematic circuit , this power amplifier use just three transistors and some other common electronic parts .
This electronic project must be powered from a 12 volt DC power supply .wer in a 16 or 32 ohms load .470 mwatts small power audio amplifier electronic project for portable applications

NCP2824 bassed Class D amplifier electronic project circuit and explanation

Using the NCP2824 filterless Class D amplifier can be designed a very simple low power audio amplifier electronic project, capable of delivering up to 2.4 W to a 4 ohms load with a 5 V supply voltage.
With the same battery voltage, it can deliver 1.2 W to an 8 ohms load with less than 1% THD+N. The non−clipping function automatically adjusts the output voltage in order to control the distortion when an excessive input is applied to the amplifier.

This adjustment is done thanks to an Automatic Gain Control circuitry (AGC) built into the chip. A simple single wire interface allows to the non Clipping function to be enabled and disabled.
A programmable power limit function is also embedded in order to protect speakers from damage caused by an excessive sound level.
2.4 watts Class D amplifier electronic project using NCP2824 amplifier IC

TA8259H bassed 4 channel car amplifier circuit and explanation

TA8259H bassed 4 channel car amplifier circuit and explanation
Using the TA8259H integrated circuit can be designed a very simple 4 ch BTL audio power amplifier for car audio application.
This IC can generate more high power: POUT MAX = 37 W as it is included the pure complementary PNP and NPN transistor output stage.

It is designed low distortion ratio for 4 ch BTL audio power amplifier, built-in Stand-by Function, Muting Function, Clip detector, and diagnosis circuit.
As you can see in the circuit diagram , this audio amplifier electronic project require extreme low external electronic parts .

Additionally, the AUX. amplifier is built-in, it can make the beep signal etc. output to 2 channels (OUT1 and 4).

Input voltage range that is accepted by this audio amplifier project is between 9 and 18 volt , but typically is required a 14,4 volts DC.
All speakers used with this amplifier circuit project , based on TA8259H IC must have a 4 ohms impedance .

STK4038 bassed 60 watt audio amplifier circuit project and explanation

STK4038 bassed 60 watt audio amplifier circuit project and explanation

Using the STK4038X audio amplifier IC, can be designed a very simple high power and efficiency audio power amplifier . This circuit is manufactured by Sanyo Corporation and will provide a output power of 60 watts on a 8 ohms load or 4 ohms load with 0.008% distortion .

The output power that is provided by this audio IC , can be more higher , but with more distortion.
If you will use a 8 ohms load you must power this audio amplifier project from a dual +/- 40 volts DC power supply and if you’ll use a 4 ohms load you must power this audio project form a dual +/- 33.5 volts DC power source.
To prevent over heating the STK4038X audio power IC must be heatsinked on a good heatsink .
Also you must use a very well filtered power supply ( a 10000uF capacitor will be fine for this audio project) .


TB2922HQ bassed 40, 70 watt power audio amplifier circuit and explanation

TB2922HQ bassed 40, 70 watt power audio amplifier circuit and explanation

Using the TB2922HQ audio power IC can be designed a very simple and high efficiency power audio amplifier electronic project . TB2922HQ is 2ch BTL audio amplifier for TV or home audio applications.

It includes and the pure complementary P-ch and N-ch DMOS output stage.
This TB2922HQ power audio amplifier project is very simple to be implemented and require few external electronic parts . The TB2922HQ power audio amplifier module can be used with 4 or 8 ohms load . Using a 4 ohms load this power audio circuit will provide a output power around 40 watts and using a 8 ohms load the circuit will provide a output power of 23 volts . If you’ll use a bridge mode connection this circuit will provide an output power around 70 watts . If is used a 4 ohms load this TB2922HQ power audio amplifier project must be powered from a good filtered DC power supply that will provide an output voltage between 9 and 18 volts , and if is used a 8 ohms load , a DC power supply that will provide a n output voltage between 9 and 26 volts will be required .
Some features provided by this audio power amplifier module are : built-in standby switch function ,built-in muting function , built-in various protection circuits: thermal shut down, overvoltage, out to GND, out to VCC, out to out short speaker burned .

STK415-090-E bassed 2x50 watt stereo amplifier circuit and explanation

STK415-090-E bassed  2x50 watt stereo amplifier circuit and explanation

This electronic project stereo amp is based on the STK415-090-E class H audio power amplifier hybrid IC that features a built-in power supply switching circuit.
This STK415-090-E class H audio power amplifier provides high efficiency audio power amplification by controlling (switching) the supply voltage supplied to the power devices according to the detected level of the input audio signal.
STK415-090-E class H audio power amplifier is pin to pin compatible with STK416-100 stereo amp .
This electronic project stereo amp will provide an 50 + 50 watts output power with 0.8 % THD , but it can provide more power , up to 80 watts with 10% THD .
STK415-090-E class H audio power amplifier supports output loads from 4 up to 8 ohms and require an input DC voltage from 27 up to 60 volts .
For 8 ohms load , voltage required by this stereo amp project are : +/- 27V for VL and +/-37V for VH .

This 2x50 watt stereo amp project must be designed so that (|VH|-|VL|) is always less than 40V when switching the power supply with the load connected. Set up the VL power supply with an offset voltage at power supply switching (VL-VO) of about 8V as an initial target.
To prevent over heating damage thermal design must be implemented and a thermoplastic adhesive resin must be used for this hybrid IC .
A value of 2.34.C/W, satisfies all required thermal resistance of the heat sink .
Electronic parts required for this 2x50 watt stereo amp electronic project are : R01, R02 1.5k ; R03, R04 100 /1W , R05, R06 56k ; R08, R09 4.7 /1W ; R11, R12 4.7, R14,R15 560 ; R18, R19 56k ; R21, R22 1k ; R24, R26 0.22 10%, 5W ; C01, C02 100.F/100V ; C03, C04 100.F/50V ; C05, C06 100.F/ 100V ; C07, C08 3pF; C10, C11 0.1.F; C13, C14 22.F/10V ; C16, C17 2.2.F/50V ; C19, C20 470pF ; C22, C23 100pF ; D01, D02 15V ; D03, D04 3A/60V ; L01, L02 3.H .

class AB power amplifier by using STA543SA

A simple class AB power amplifier electronic project can be designed using the STA543SA a 3-channels audio amplifier IC with DC volume control dedicated for each single channel. STA543SA it is a device suitable for 2.1 audio system thank to its output configuration with two single ended channels and one bridge. This class AB power amplifier based on the STA543SA will provide a 24 watts output power on a single channel and 7 watts output power on the rest of channels . All output channels require a 4 ohms load .The Short Circuit Protection, the Thermal Protection and the Diagnostics Functions are integrated in the STA543SA power amplifier IC.
With this class AB power amplifier it is possible to amplify three analog signals Left, Right, Subwoofer coming from separated sources or to generate the BASS part to be sent to the Subwoofer via a passive crossover network .
The input Cut-off frequency is set by the external capacitor (C4,C8,C10) values and by the internal Input Impedance Rin ( 30KΩ typ) .
The stand-by can be easily activated by means of a CMOS level applied to pin 9 through a RC filter. In order to avoid the thermal protection intervention that is placed at Tj=150°C (Thermal Muting) or Tj=160°C (Thermal Shut-down), it is important the Heat Sinker RTH (°C/W)dimensioning.
A thermal heatsink with a value 4.3 °C/W will be required for three outputs (24W + 2 x 7 W) powered from a 14.4 volts DC .
class AB power amplifier by using STA543SA