| Parameter Name | Value |
| Architecture | 16-bit |
| CPU Speed (MIPS) | 40 |
| Memory Type | Flash |
| Program Memory (KB) | 64 |
| RAM Bytes | 8,192 |
| Temperature Range C | -40 to 125 |
| Operating Voltage Range (V) | 3 to 3.6 |
| I/O Pins | 85 |
| Pin Count | 100 |
| System Management Features | PBOR |
| Internal Oscillator | 7.37 MHz, 512 kHz |
| nanoWatt Features | Fast Wake/Fast Control |
| Digital Communication Peripherals | 2-UART, 2-SPI, 2-I2C |
| Analog Peripherals | 1-A/D 32×12-bit @ 500(ksps) |
| CAN (#, type) | 1 ECAN |
| Capture/Compare/PWM Peripherals | 8/8 |
| 16-bit PWM resolutions | 16 |
| Timers | 9 x 16-bit 4 x 32-bit |
| Parallel Port | GPIO |
| Hardware RTCC | No |
| DMA | 8 |
| XLP | NO |
Features
Operating Range:
# DC – 40 MIPS (40 MIPS @ 3.0-3.6V, -40°C to +125°C)
# Extended temperature range (-40°C to +125°C)
High-Performance DSC CPU:
# Modified Harvard architecture
# C compiler optimized instruction set
# 16-bit wide data path
# 24-bit wide instructions
# Linear program memory addressing up to 4M instruction words
# Linear data memory addressing up to 64 Kbytes
# 71 base instructions: mostly 1 word/1 cycle
# Sixteen 16-bit General Purpose Registers
# Flexible and powerful Indirect Addressing modes
# Software stack
# 16 x 16 multiply operations
# 32/16 and 16/16 divide operations
# Up to ±16-bit data shifts
Direct Memory Access (DMA):
# 8-channel hardware DMA
# 2 Kbytes dual ported DMA buffer area (DMA RAM) to store data transferred via DMA: – Allows data transfer between RAM and a peripheral while CPU is executing code (no cycle stealing)
# Most peripherals support DMA
Interrupt Controller:
# 5-cycle latency
# 118 interrupt vectors
# Up to 61 available interrupt sources
# Up to 5 external interrupts
# 7 programmable priority levels
# 5 processor exceptions
Digital I/O:
# Wake-up/Interrupt-on-Change on up to 24 pins
# Output pins can drive from 3.0V to 3.6V
# All digital input pins are 5V tolerant
# 4 mA sink on all I/O pins
System Management:
# Flexible clock options: – External, crystal, resonator, internal RC – Fully integrated PLL – Extremely low jitter PLL
# Power-up Timer
# Oscillator Start-up Timer/Stabilizer
# Watchdog Timer with its own RC oscillator
# Fail-Safe Clock Monitor
# Reset by multiple sources
Power Management:
# On-chip 2.5V voltage regulator
# Switch between clock sources in real time
# Idle, Sleep and Doze modes with fast wake-up
Timers/Capture/Compare/PWM:
# Timer/Counters, up to nine 16-bit timers: – Can pair up to make four 32-bit timers – 1 timer runs as Real-Time Clock with external 32.768 kHz oscillator – Programmable prescaler
# Input Capture (up to 8 channels): – Capture on up, down or both edges – 16-bit capture input functions – 4-deep FIFO on each capture
# Output Compare (up to 8 channels): – Single or Dual 16-Bit Compare mode – 16-bit Glitchless PWM mode
Communication Modules:
# 3-wire SPI (up to 2 modules): – Framing supports I/O interface to simple codecs – Supports 8-bit and 16-bit data – Supports all serial clock formats and sampling modes
# I2C™ (up to 2 modules): – Full Multi-Master Slave mode support – 7-bit and 10-bit addressing – Bus collision detection and arbitration – Integrated signal conditioning – Slave address masking
# UART (up to 2 modules): – Interrupt on address bit detect – Interrupt on UART error – Wake-up on Start bit from Sleep mode – 4-character TX and RX FIFO buffers – LIN bus support – IrDA® encoding and decoding in hardware – High-Speed Baud mode – Hardware Flow Control with CTS and RTS
# Enhanced CAN (ECAN™ module) 2.0B active (up to 2 modules): – Up to 8 transmit and up to 32 receive buffers – 16 receive filters and 3 masks – Loopback, Listen Only and Listen All Messages modes for diagnostics and bus monitoring – Wake-up on CAN message – Automatic processing of Remote Transmission Requests – FIFO mode using DMA – DeviceNet™ addressing support
Analog-to-Digital Converters:
# Up to two A/D modules in a device
# 10-bit, 1.1 Msps or 12-bit, 500 ksps conversion: – 2, 4 or 8 simultaneous samples – Up to 32 input channels with auto-scanning – Conversion start can be manual or synchronized with 1 of 4 trigger sources – Conversion possible in Sleep mode – ±2 LSb max integral nonlinearity – ±1 LSb max differential nonlinearity
CMOS Flash Technology:
# Low-power, high-speed Flash technology
# Fully static design
# 3.3V (±10%) operating voltage
# Extended temperature
# Low-power consumption
