Showing posts with label Detector. Show all posts
Showing posts with label Detector. Show all posts

Lie detector circuitwith explanation

Lie detector circuitwith explanation

Here’s a simple lie detector that can be built in a few minutes, but can be incredibly useful when you want to know if someone is really telling you the truth. It is not as sophisticated as the ones the professionals use, but it works. It works by measuring skin resistance, which goes down when you lie.

Here are the details of the specific parts you will need

Part Total Qty. Description Substitutions

R1 1 33K 1/4W Resistor
R2 1 5K Pot
R3 1 1.5K 1/4W Resistor
C1 1 1uF 16V Electrolytic Capacitor
Q1 1 2N3565 NPN Transistor
M1 1 0-1 mA Analog Meter
MISC 1 Case, Wire, Electrodes (See Nots)

Notes
1. The electrodes can be alligator clips (although they can be painful), electrode pads (like the type they use in the hospital), or just wires and tape.

2. To use the circuit, attach the electrodes to the back of the subjects hand, about 1 inch apart. Then, adjust the meter for a reading of 0. Ask the questions. You know the subject is lying when the meter changes.

http://www.aaroncake.net/circuits/lie.htm

ULN2429A based liquid detector circuit diagram circuit with explanation

ULN2429A based liquid detector circuit diagram circuit with explanation
ULN2429A based liquid detector circuit diagram circuit with explanation

This electronic liquid detector circuit diagram is based on the ULN2429A monolithic bipolar integrated circuit designed for detecting the absence or presence of many different types of liquids . The ULN2429 electronic liquid detector circuit can be used in automotive , home or industrial applications .
The absence or presence of the liquid is determined by comparing the loaded probe resistance (probe immersed in the fluid ) with an internal or external resistance . At the output you can connect a LED , incandescence lamp , loud speaker or even such relays or solenoids, but just I you connect at pin 12 a capacitor , to provide a dc output ( typically the output signal is a square wave ) .

If you need to connect at the output a device that need more than 30 volts you can use the ULN2429A-1 which is identical , but support devices with operation up to 50 volts .

Main features of the ULN2429A are : high output current , AC or DC output , single wire probe , low external parts require , reverse voltage protection , internal voltage regulation .
This fluid detector electronic circuit need to be powered using a power supply that provide an output voltage between 10 and 16 volts .

Frost Detector Temperature Sensor Circuit [Frost Detector Temperature-Sensor] To know whether it is freezing you only need to measure the temperature



To know whether it is freezing you only need to measure the temperature. This has to be done accurately, of course, and therefore we need to choose a temperature sensor that we have some confidence in. The choice has again been made for a type that we have already used in many previous Elektor circuits, the LM35CZ (-40 to 110 °C). This sensor is not expensive and generates an output voltage that is proportional to the temperature in degrees Celsius (10 mV/°C).

Sensor
An LM35 is normally powered from a single-ended power supply and 0 °C corresponds to an output voltage of 0 V. It is therefore not possible to measure negative temperatures with an LM35 in the standard application circuit. It is however possible to measure negative temperatures if its output is connected to a negative supply voltage via a resistor. There needs to be a current of 50 μA through this resistor (R2 in the schematic).



We only need to detect the freezing point with this circuit. That is why there is a comparator after the temperature sensor, which turns an LED on if the temperature has dropped below 0 °C during the course of the night. To ensure that the comparator operates properly it is necessary that the measurement value can become slightly more negative with respect to the input. To solve this problem, a diode (D1) has been connected in series with the ground connection of the LM35. The voltage drop across D1 (because of the small current through the LM35 this is only 0.47 V) acts as 'negative' power supply. Since the non-inverting input of comparatorIC2 is connected via R3 to the anode of D1 it functions as the 0°C-reference level for the comparator.

Comparator
The comparator is a standard opamp type TLC271, which we configured for minimal current consumption by
connecting the bias-select input (pin 8) to the power supply voltage. There is no need for the detector to be fast and it will therefore work well with the opamp operating in its most economical mode.

LED D3 provides the frost indication. It is the intention that the LED stays on once the temperature in the room drops below freezing or when it has been below freezing. To realise this, an asymmetric hysteresis is created with the aid of R3, R4 and D2. The instant that the output goes high, the non-inverting input goes more positive via D2 and R4, and the output therefore stays high. The temperature would now have to increase to more than about 30° before the LED will go out by itself. In practice this probably means that it is summer and that it is not likely to freeze anyway. If need be, the hysteresis can be increased by increasing the value of R3.



Capacitor C2 is added to make sure that the LED remains off (the circuit is reset) when the power supply is connected. The non-inverting input of the opamp is briefly connected to ground and the output is therefore low. R1 and S1 are only required if the circuit needs to be reset when the battery is connected. Instead of S1 you could also use a power supply switch or even just simply disconnect the battery for a moment.

Thrifty Power supply
Since the circuit is assumed to be powered from a battery there was a conscious effort to minimise the power consumption. The current consumption of the prototype, at a power supply voltage ranging from 6 to 9 V, was less than 120 μA. When the LED is on, the current consumption rises to only 1 mA at 6V and 1.8 mA at 9V, because a low current LED is used. In our prototype we used a green, low-current LED.

If four AA penlight batteries (with a capacity of about 2 Ah) are used, then the circuit will run for about two years in standby mode. When the LED is on this is considerably shorter, of course (about two months, this is easily long enough to run through a severe winter period). A standard 9-V battery will also last a single winter, provided you frequently check whether the LED is on.

Finally, a comment about the TLC-271CP used here. The version with the C-suffix is specified for an operating range from 0 to 70 °C, but will continue to work at lower temperatures, particularly considering that the IC is not used in a linear application. If in doubt you can always try to get your hands on a version with the I-suffix (that is, TLC271IP: –40 to 125°C). But that is only necessary if you expect it to be real cold in the monitored room...

Quick assembly
The circuit contains very few parts and can therefore be easily built on a small piece of prototyping board. There is no need to calibrate anything, once built it is ready to go. Author: Ton Giesberts, Elektor Magazine, 2008.

latest Light Detector by IC CD4001 circuit and explanation

Variable resistor R1 adjusts the light threshold at which the circuit triggers. R1’s value is chosen to match the photocells resistance at darkness. The circuit uses a CMOS 4001 IC. Gate U1a acts as the trigger, U1b and c form a latch. S1 resets the circuit. The output device may be a low power piezo buzzer.

Kindly submitted by Mick Devine from the UK
Source :: http://www.zen22142.zen.co.uk/Circuits/Switching/ldet.htm

New Frost Detector Temperature Sensor Circuit



To know whether it is freezing you only need to measure the temperature. This has to be done accurately, of course, and therefore we need to choose a temperature sensor that we have some confidence in. The choice has again been made for a type that we have already used in many previous Elektor circuits, the LM35CZ (-40 to 110 °C). This sensor is not expensive and generates an output voltage that is proportional to the temperature in degrees Celsius (10 mV/°C).

Sensor
An LM35 is normally powered from a single-ended power supply and 0 °C corresponds to an output voltage of 0 V. It is therefore not possible to measure negative temperatures with an LM35 in the standard application circuit. It is however possible to measure negative temperatures if its output is connected to a negative supply voltage via a resistor. There needs to be a current of 50 μA through this resistor (R2 in the schematic).



We only need to detect the freezing point with this circuit. That is why there is a comparator after the temperature sensor, which turns an LED on if the temperature has dropped below 0 °C during the course of the night. To ensure that the comparator operates properly it is necessary that the measurement value can become slightly more negative with respect to the input. To solve this problem, a diode (D1) has been connected in series with the ground connection of the LM35. The voltage drop across D1 (because of the small current through the LM35 this is only 0.47 V) acts as 'negative' power supply. Since the non-inverting input of comparatorIC2 is connected via R3 to the anode of D1 it functions as the 0°C-reference level for the comparator.

Comparator
The comparator is a standard opamp type TLC271, which we configured for minimal current consumption by
connecting the bias-select input (pin 8) to the power supply voltage. There is no need for the detector to be fast and it will therefore work well with the opamp operating in its most economical mode.

LED D3 provides the frost indication. It is the intention that the LED stays on once the temperature in the room drops below freezing or when it has been below freezing. To realise this, an asymmetric hysteresis is created with the aid of R3, R4 and D2. The instant that the output goes high, the non-inverting input goes more positive via D2 and R4, and the output therefore stays high. The temperature would now have to increase to more than about 30° before the LED will go out by itself. In practice this probably means that it is summer and that it is not likely to freeze anyway. If need be, the hysteresis can be increased by increasing the value of R3.



Capacitor C2 is added to make sure that the LED remains off (the circuit is reset) when the power supply is connected. The non-inverting input of the opamp is briefly connected to ground and the output is therefore low. R1 and S1 are only required if the circuit needs to be reset when the battery is connected. Instead of S1 you could also use a power supply switch or even just simply disconnect the battery for a moment.

Thrifty Power supply
Since the circuit is assumed to be powered from a battery there was a conscious effort to minimise the power consumption. The current consumption of the prototype, at a power supply voltage ranging from 6 to 9 V, was less than 120 μA. When the LED is on, the current consumption rises to only 1 mA at 6V and 1.8 mA at 9V, because a low current LED is used. In our prototype we used a green, low-current LED.

If four AA penlight batteries (with a capacity of about 2 Ah) are used, then the circuit will run for about two years in standby mode. When the LED is on this is considerably shorter, of course (about two months, this is easily long enough to run through a severe winter period). A standard 9-V battery will also last a single winter, provided you frequently check whether the LED is on.

Finally, a comment about the TLC-271CP used here. The version with the C-suffix is specified for an operating range from 0 to 70 °C, but will continue to work at lower temperatures, particularly considering that the IC is not used in a linear application. If in doubt you can always try to get your hands on a version with the I-suffix (that is, TLC271IP: –40 to 125°C). But that is only necessary if you expect it to be real cold in the monitored room...

Quick assembly
The circuit contains very few parts and can therefore be easily built on a small piece of prototyping board. There is no need to calibrate anything, once built it is ready to go. Author: Ton Giesberts, Elektor Magazine, 2008.

Tone Detector circuit diagrams and explanation

The following circuit diagrams are tone detector circuit diagrams which also known as sound activated switch circuit. Actually, these circuits use micro-controller for switching because the circuits were designed for robot start up activation. But you can build switching module using relay.

Tone Detector diagram 1

Tone Detector circuit diagram schematic

Tone Detector diagram 2

Tone Detector schematic diagram

Tone Detector diagram 3

Tone Detector circuit

Tone Detector diagram 4

Tone Detector diagram

Tone Detector diagram 5

Tone Detector circuit diagram

Source: Sound activated switch for robot

Simple Rain Detector circuit and explanation

Here's a simple rain detector circuit. It uses a sensor made of a small piece of etched PC board and a simple SCR circuit to detect rain and sound a buzzer. The SCR could also be used to activate a relay, turn on a lamp, or send a signal to a security system.



Rain Sensor and Alarm
The sensor made of a small piece of PC board etched to the pattern showen in the schematic. The traces should be very close to each other, but never touching. A large spiral pattern would also work. A loud buzzer used as an alarm.

Rain Detector Parts List

R1 = 1K 1/4 W Resistor
R2 = 680 Ohm 1/4 W Resistor
D1 = 1N4001 Silicon Diode
BZ1 = 12V Buzzer
S1 = SPST Switch
SCR1 = C106B1 SCR 106CY
SENSOR = See Notes
MISC = Board, Wire, Case, PC Board (For Sensor)

More about rain detector